U-channels and box sections
A U-channel, as the name implies, comprises
two right-angled bends, one at each of the opposite
sides of a piece of metal (Figure 5.4).
Much more strength can be gained by making a
U-channel instead of a single-angled bend in
any reinforcement section. The U-channel is also
the most common type of section used in the
construction of car frames. Yet another method
of increasing strength is known as box construction,
which consists of two U-sections welded
together to form a square pillar or box. Box
sections are used in conjunction with U-channel
construction in the manufacture of car chassis
frames, underbodies, subframes, cross members
and any construction where great strength is
necessary.
Figure 5.2Strength in crowned surfaces
Figure 5.3Strength in angles and flanges Figure 5.4Strength in U-channel and box sections
Metal forming processes and machines 169
5.4 Machines for sheet metal fabrication
The mass produced, all-steel bodies of both private
cars and light commercial vehicles call for the production
of involved panel shapes on a massive
scale. This requires heavy power presses employing
mating die sets which in effect press the sheet
metal and deform the structure of the metal to a
degree where it takes on a natural shape and retains
that shape. However, since all pressed panels have
some degree of tension in the material structure, it
is important that this should be taken into account
by the body repairer.
It is often necessary to manufacture sheet steel
parts by metal forming machines. The most common
of these include wheeling machines, guillotines,
fly presses, folders and forming presses. In
body repair shops the fly press is often hand operated,
and is a most useful piece of equipment. Tools
for the fly press fit into a central spindle which is
moved down in order to pierce, blank and to a limited
extent form the metal parts required. Another
widely used machine is the folder or bending
machine; adjustment of the setting of the blades of
this machine enables sharp acute or obtuse angled
bends to be produced in long lengths of sheet metal
for the making of sections. The swaging machine is
used for swaging, wiring, joggling and closing
sheet metal work edges. Finally, the body shop is
not complete unless it possesses a wheeling
machine, which is used to produce double curvature
panels from flat sheets by passing the sheets to and
fro between rollers or wheels in order to stretch the
sheets and to create a curved shape.
5.5 Shearing theory
If a piece of sheet metal is placed on one bottom
cutting member or blade, and the top cutting blade
is brought to bear on the metal with continuing
pressure, after a certain amount of deformation the
elastic limit of the metal is exceeded and the top
cutting blade penetrates and cuts the surface of the
metal (Figure 5.5). Fractures begin to run into the
metal thickness from the points of contact of the
top and bottom cutting blades, and if these are positioned
correctly relative to each other, the fractures
meet and the metal is sheared before the top member
penetrates and cuts the whole thickness of the
metal. The horizontal distance between the two cutting
members is called the clearance (Figure 5.6),
and it is this distance that determines the quality of
the cut and the load on the machine or hand tool
being used. There is only one correct clearance
allowance for any particular sheet, and this
depends mainly upon the thickness of the metal
being cut and its physical properties. This clearance
allowance is usually 5–10 per cent of the metal
thickness.
5.6 Cutting machines
Hand lever shears
There are the simplest sheet metal working
machines. For cutting mild steels they are used
with blade lengths up to 500 mm for cutting 3 mm
material, or with a length of about 200 mm for
material up to 6 mm. The cutting members are flat
blades and there is generally no provision for
adjustment of blade clearance. The bottom blade is
fixed to the machine frame, while the top cutting
blade is fixed to a moving member which is pivoted
in the main frame and operated by a hand
lever via a simple link mechanism. An adjustable
Figure 5.5The cutting section showing a sheared
piece of metal
Figure 5.6Blade clearance
170Repair of Vehicle Bodies
hold-down is usually fitted to the top member to
hold the sheet down during cutting. The body of
the shears may be cranked or offset to permit the
cut sheets to be forced beyond the blades so that
sheets longer than the blades may be cut. The body
of the machine is usually fabricated, and this construction
is to be preferred.