Vehicle repair weld testing quality
control BS EN ISO 9001–2000
Those vehicle body repair companies wishing to
obtain British Standards will have to conduct weld
test procedures. These procedures will have to
become an integral part of the company’s policy on
quality in the repair of vehicles while maintaining
safe working practices. In addition regular testing
will demonstrate the skill and ability of body technicians
to maintain a high quality of weld standard
in all types of crash repair work carried out by
their company.
12.16 Equipment maintenance and safety
For the best results the gas and contact nozzle of
the welding torch must be cleaned of welding spatter
at regular intervals. Unless this is done, there is
a risk of the welding current arcing between the
contact nozzle and the gas nozzle to the workpiece,
which could cause severe damage to the welding
torch. When cleaning the gun of spatter and
deposits the condition of the gas distributer should
also be checked, and if it appears to be burnt and
worn by spatter then it should be replaced. This is
because in addition to distributing the gas it also
acts as an insulator, and is of vital importance to
the service life of the swan neck of the torch. It is
recommended that the machine should be cleaned
with compressed air once yearly, or more frequently
if it is used in dusty conditions. The feed
mechanism and rollers require more frequent
cleaning. Regular maintenance to the following
parts is important: gas nozzle, gas distributor, contact
nozzle and wire guide rollers. It is never advisable
to weld with a worn-out contact nozzle and
deformed gas nozzle.
Any exposure to a naked welding arc, even for a
fraction of a second, is sufficient to damage the
cornea of the eye (welding flash). Consequently a
welding screen should always be used, preferably
Gas shielded arc welding 341
of the helmet and visor type. By using this type
both hands are free for control over the welding
equipment. The hand-held type of welding screen
is of course fully adequate from a safety point of
view but only leaves one hand free. This could
result in a shakier movement of the gun and a loss
of precision in following the joint.
Wear welding gloves and suitably fitting protective
clothing, especially when welding overhead so
that the welding spatter does not run down the
neck or sleeves of the overall worn.
Another hazard is the build-up of fumes given
off by the welding process, which could be dangerous
to health when welding in a confined space.
When welding in a normal workshop there is no
problem, but if welding in a tightly enclosed area,
such as inside the boot of a car, make sure that the
area is well ventilated.
Precaution must be taken when welding vehicle
panels in case there are flammable materials
attached to the other side of the panel which could
ignite and burst into flames. Therefore always have
adequate fire-fighting appliances available.
Questions
1 Explain the term ‘MIG/MAG welding’.
2 Explain the term ‘TIG welding’.
3 What is an inert gas? Explain its function in
welding.
4 What are the advantages of gas shielded arc
welding?
5 Name three types of gases that could be used in
MIG/MAG welding.
6 What is the difference between water-cooled and
air-cooled torches in TIG welding?
7 What determines the size of the ceramic nozzle
to be used for TIG welding?
8 Which material are the electrodes made from in
the TIG welding process?
9 State the advantages of MIG/MAG welding when
compared with oxy-acetylene welding, for the
repair of vehicle panels.
10 When MIG welding aluminium and its alloys,
which type of gas would be most suitable for use?
11 Describe the difference between plug welding
and spot welding.
12 Explain the mode of metal transfer used for
welding thin-gauge materials.
13 Describe the three functions that most MIG/MAG
welding equipment is capable of performing.
14 Explain the term ‘spray transfer’.
15 Describe the purpose of a contact tip in a
MIG/MAG welding torch.
16 Show, with the aid of a sketch, a repair situation
where resistance spot welding can be substituted
by a MIG/MAG spot weld.
17 With the aid of diagrams, describe the following
defects made by MIG/MAG welding: (a) porosity
(b) incomplete fusion (c) spatter on workpiece (d)
poor penetration.
18 What colours are used to identify argon and
argon-mix cylinders?
19 Why is it important to disconnect a battery on a
vehicle before commencing any MIG/MAG
welding operation?
20 List the safety precautions to be observed before
and during welding.
21 Explain the form in which the electrode is
manufactured for MIG/MAG welding.
22 With the aid of a sketch, show a repair application
which involves MIG/MAG spot welding.
23 Describe the major features of a TIG welding torch.
24 Which mode of metal transfer uses the short-arc
process in MIG/MAG welding?
25 With the aid of a sketch, illustrate one method of
metal transfer used in MIG/MAG welding.
26 With the aid of a sketch, explain how plug
welding is carried out in repair work.
27 Describe the differences between the processes
of TIG welding and MIG/MAG welding.
28 By using a sketch, illustrate a typical weld fault in
MIG/MAG welding.
29 State the function of the controls of standard
MIG/MAG welding equipment.
30 Explain the setting to be used when welding a
large gap with MIG/MAG welding.
Craft techniques
and minor
accident damage
13.1 Panel beating: forming panels
by hand
Essentially, panel beating is a hand method of
producing hollow or double-curvature shapes by
means of hammering. Nevertheless, the panel
beater’s craft still retains its place in body work and
as yet is irreplaceable by more modern methods;
in spite of the tremendous developments in recent
years of mechanical methods of forming, panel
beating remains an essential means of fabrication of
special parts. Some metal shapes cannot be
produced at all by mechanical methods and others
only with great difficulty, and in such cases panel
beating is used to finish the shape that has been
roughed out by power processes. Often, too, the prototype
of a component ultimately to be made
in quantity by stamping or pressing is hand made to
allow minor modifications to be studied before
mechanical production begins; the part produced by
panel beating is used as the pattern for press or
stamp tools. Panel beating may also be used where a
small number of components only are required and
where the cost of press or stamp tools would be
uneconomic. In body repair work, panel beating is
used to advantage where sections which are either
unobtainable or uneconomical to replace completely
can be fabricated by hand either in part or as a
whole. In many cases corroded areas can be repaired
by fabricating new sections for replacement purposes.
In the body building trade, panel beating is
still used to a large extent where new vehicles are
being built either in aluminium or mild steel. Many
of the components for these vehicles are still made
using the traditional hand shaping methods. Also a
lot of the aluminium moulds used in fibreglass construction,
where highly developed double-curvature
shapes are needed, are made by hand, welded and
dressed and planished or wheeled to a final finish.
Panel beating is essentially a hammering process,
involving different kinds of blows that can be
struck on sheet metal. It should be borne in mind
that most metals used in body work possess high
malleability and may be overstretched even with
a wood tool. The types of blow that can be struck
on sheet metal are three:
Solid blow, where the work is struck solidly over
a steel stake.
Elastic blow, where either the head or the tool or
both is made of a resilient material such as wood.
Floating blow, where the stake is not directly
under the hammer.
Each type of blow has its uses for particular
purposes. A solid blow will stretch the sheet, and
may be necessary when forming a panel, bending
a curved strip or angle, removing a loose or tight
place in a sheet, or throwing an edge over when
thickness is not a consideration. An elastic blow will
form metal without undue stretching; indeed, metal
can be thickened if desired, as in working out a tuck
or pucker. The floating blow is given to the metal
when it is held over a suitable head and hit ‘off the
solid’, so forming ‘dents’ at the points of impact.
13.2 Shaping metal by hand
Thin-gauge mild steel and light aluminium sheet
material up to 1.2 mm, and in some cases even
1.6 mm, can be satisfactorily hand beaten by wood
Another method is that of raising the metal by
means of floating blows over steel stakes or wood
formers. This raising process can be speeded up
considerably by ‘taking in’ or making tucks at the
edges of the metal. This method is generally called
puckering, and after being made each pucker must
be eliminated by careful blows to drive the metal
into itself, so thickening the work at the edges.
Much greater advantage may be taken of puckering
in aluminium alloy sheet than in most metals
because of its malleability and ductility. The exact
degree of shaping of the metal which is permissible
depends upon the particular alloy being worked, its
malleability and the ability of the craftsman.
Another method of shaping metal which can be
used in conjunction with hollowing and raising is
that of wheeling. A panel can either be wheeled
from a flat sheet to the desired double-curvature
shape, or it can be preshaped using either hollowing
or raising techniques and its final shaping and
smoothing completed by wheeling. The technique
of wheeling is not entirely done by hand, as a
wheeling machine is used. The finished result
depends on the skill of the craftsman as he manipulates
the sheet by hand in the wheeling machine.
An experienced panel beater uses the beating
method suitable to the job in hand, complex shapes
often being beaten up by using both hollowing
and raising or wheeling methods. For light-gauge
material too much hollowing or blocking is not
to be recommended, as it tends unduly to thin the
metal. The skilled panel beater is a craftsman who,
to a great extent, relies on a good eye for line and
form; this can only be cultivated by years of experience
which, combined with dexterity in the use of
hand tools, is the secret of his craftsmanship. Wood
formers or jigs, upon which the beaten shape can
be tried in order to obtain uniformity of shape for
each workpiece, are used for many jobs. The shape
of the job is retained in the vision of the panel
beater, who can, by beating on the sandbag and
raising over a suitable stake, obtain a very good
approximation to the desired form. This only needs
hammering lightly on the wood former to obtain
the finished shape. Until the metal fits the former it
is often necessary to check repeatedly to find any
high or low areas which may prevent the workpiece
from fitting the former correctly. Instead
of using formers or jigs many panel beaters use
templates only, which are cut to the shape of the
various cross-sections of the workpiece. These
templates are used towards the end of the beating
process to check the finished shape of the job.
After shaping, the surface of the finished panel
has to be smoothed by the technique of planishing,
using a steel bench stake, or by wheeling.
Hollowing
One of the methods of shaping metal by hand is that
of hollowing (Figure 13.2). In this method the metals
used for the purpose of shaping panels for body
work applications are usually aluminium and its
alloys and mild steel; aluminium is by far the easier
of the two to shape owing to its higher ductility and
malleability properties. This is a process of shaping a
sheet metal blank into a double-curvature shape by
beating the blank into a sandbag or hard wood block
with the aid of a pear-shaped boxwood mallet, or for
thin metal a rubber mallet, or for steel a hollowing
hammer with a steel head.
First the blank which is going to be shaped is cut
to size and the edges trimmed for any rag by filing.
If this rag is not removed as the blank is shaped, it
may tend to split from the edge of the rag. The next
step is to place the metal blank, which should be
held tilted, on to a sandbag, and to give it a series
Craft techniques and minor accident damage 343
Figure 13.1Shaping metal by hand
mallets into double curvature forms (Figure 13.1).
The usual practice is to beat the metal in a suitable
recess in a wood block or upon a sandbag in what
is known as the hollowing or blocking process.
Alternatively, the metal can be hammered into a
wood block hollowed out to the shape of the job.
344Repair of Vehicle Bodies
of blows around its outside edge, working towards
the centre by means of a pear-shaped mallet. This
hammering has the effect of sinking the metal into
the sandbag, which is of course resilient to the
blows. After each blow the disc is turned and the
next blow struck near the first one, and so on until
a series of overlapping blows is made round the
circumference of the blank. The tendency will be
for creases or wrinkles to appear on the edges of
the metal and these must be gently malleted flat to
avoid overlapping of the metal and eventual cracking.
The hammering of each course has to be done
with steady and even blows to bring up a regular
curved shape. On completion of the first course of
blows, a second course is begun further in from the
edge of the metal than the first set. This process of
hammering in courses and rotating the blank is
continued until eventually the centre of the blank
is reached; by this time it will have taken on a
double-curvature shape, but should greater depth
be required the whole operation must be started
again, working gradually from the edge towards
the centre of the work until it is completely to the
desired shape and size (Figure 13.3).
At this stage templates cut to the correct size
and shape can be used to check that the panel
being shaped is the correct size and curvature.
Alternatively it is possible to use a jig constructed
to the correct size and shape, usually in wood. It
may be necessary during the beating-up process to
anneal the work-piece to restore its malleability,
because the hammering tends to harden the metal
by work hardening. In some cases, instead of using
a sandbag for the shaping to be carried out on, a
hollowed-out recess in a wood block can be used.
When the panel has reached the desired shape by
hollowing it can then be smothed to a final finish
by hand planishing using a hand dolly or over a
stake, or wheeling to obtain the final smoothness.
Raising
Raising is another method of shaping metal by
hand into a double-curvature shape (Figure 13.4).
The method of raising is carried out by drawing
the metal in courses over a suitably shaped steel
stake or wood block, using floating blows which
are struck slightly off the stake with a boxwood
pear-shaped mallet. A series of blows is made in
the metal starting at the centre, the blows being
struck slightly off the stake. This has the effect
of shrinking or reducing the circumference of the
blank, thus forcing it down and around the stake.
The disc or blank is rotated after each blow as in
hollowing, but working from the centre in courses
outwards towards the edges of the blank. The same
process is repeated with frequent annealing of the
metal until the final degree of raising is reached
Figure 13.2The technique of hollowing
Figure 13.3A panel being shaped by hollowing
(Frost Auto Restoration Techniques Ltd )
Craft techniques and minor accident damage 345
and the desired shape obtained (Figure 13.5). In
the course of the raising, the edges of the metal
around the circumference will be continually subjected
to creasing, and care and skill is needed to
avoid allowing these creases to become too sharp.
If they are not worked out the edge will crack or
fracture as the shape proceeds.
tuck is lightly malleted to stiffen the metal and
hold the tuck in position. This is done in three or
four places on the circumference of the blank, thus
decreasing its diameter. Then working from the
base or point of the tuck, this surplus metal is
malleted out over a stake towards the edge of the
disc. This has to be done very carefully with the
minimum of blows, and overlapping must not take
place. As each tuck is formed and worked out,
the blank deepens towards its final shape.
The processes of hollowing and raising in sheet
metal are often applied together in the making of
articles in the form of double-curvature shapes,
bowl-like shapes, etc. When the work is only
slightly domed, the process of hollowing alone
may be sufficient to complete the work. There are
limitations to the depth which can be obtained by
hollowing. This is governed by the diameter of the
finished article and access for hand tools. Where
the diameter is going to be small and the article
deep, the raising method will have to be used to
shape the work. Again as in the hollowing process,
the final finish can be obtained by planishing the
preshaped article to a smooth surface finish.
Wheeling
The craft of wheeling has been used for many
years in the production of curved panel assemblies
that are used to make up the modern vehicle body.
Wheeling was a very skilled art when vehicles were
coach built and hand methods were employed to
make the component panels (Figure 13.7). With the
advent of mass production and the development
of the motor car, speed of production became an
essential factor. Consequently hand-made panels,
Figure 13.4Raising
Figure 13.5A panel being shaped by raising (Frost
Auto Restoration Techniques Ltd )
Figure 13.6A pucker or tuck made at the edge of
the panel to quicken the raising process
When the article is partly beaten up over the
stake, a series of tucks can be made in the outer
edges of the work in order to quicken up the beating
or raising process by taking in or shrinking
surplus metal. This method is to make a pucker
or tuck at any point on the edge of the blank by
bending the metal on a stake into an ear-shaped
form (Figure 13.6). After the tuck is formed, the
disc is placed on a steel stake and each side of the
346Repair of Vehicle Bodies
which were usually made by wheeling, were
replaced by pressed panels made on power presses
with mating dies, which very speedily produced
accurate panels having a good surface finish.
Today wheeling is still used to produce panels for
prototype vehicles; one-off assemblies which are
specially built to order, and small-volume production,
where the panels are prepressed to somewhere
near the finished shape and then finished
off by wheeling (Figures 13.8 and 13.9). The vehicle
building industry still uses wheeling in producing
panels for commercial and private coaches,
road transport vehicles and any assembly requiring
a double-curvature shape in its production.
The art of wheeling lies in the operator’s ability
to handle the panel successfully in the wheeling
machine (Figure 13.10). Wheeling is simply the
stretching of metal between two steel rolls known
as wheels. The upper wheel has a flat face and
revolves freely on its own bearings. The lower
wheel also revolves but has a convex curved face
and is made interchangeable so that different shaped
lower wheels, from nearly flat to full curved, can
be used. The two wheels meet at a common centre
at which the stretching takes place when the wheels
are tensioned by applying pressure through the
bottom wheel against the panel which is pressed
on to the top wheel. As the metal panel is pushed
through the wheels a stretched area, the length of
Figure 13.7Wheeling a panel to restore a vintage
vehicle (Frost Auto Restoration Techniques Ltd )
Figure 13.8Sports car panel being shaped by
wheeling (Autokraft Ltd )
Figure 13.9Sports car panel being shaped by
wheeling (Autokraft Ltd )
Craft techniques and minor accident damage 347
the panel, is produced, and is known as the wheel
track. By carefully allowing these wheel tracks to
overlap on the entire surface of the flat panel being
wheeled, a curve in one direction only develops.
To create double curvature on the same panel,
stretching must take place in two opposing directions;
therefore a second set of wheel tracks must
cross the first set transversely, and this is achieved
by turning the panel through approximately 90°
before making the second tracks. As the panel is
pushed through the wheels the pressure can be
increased gradually until the desired curvature is
obtained. Therefore the skill of wheeling lies in
the use of correct wheel pressures and careful
manipulation of the panel through the wheels; this
can only be learnt by experience. An alternative
method of achieving double curvature on a flat
panel is to form the first curve by using a rolling
machine, and then to wheel it in one direction only,
allowing the tracks to cover the panel in the opposite
direction to the first curve, thus stretching the
metal in such a way to form the double curvature
shape. Wheeling can therefore be used, first, for
shaping a flat metal blank to a finished doublecurved
panel; second, to finish a preshaped panel
which has been hollowed or raised to its final
shape; and third, to smooth or planish a preshaped
panel to its final finish.
The materials best suited for wheeling are
aluminium, some of the aluminium alloys and mild
steel, all of which possess the properties of
malleability and ductility to a certain degree.
When using the wheeling machine for wheeling
aluminium and its alloys, care should be taken not
to put too much pressure on the work of raising
the bottom wheel. Up to three times as much
lift or stretch is obtainable with aluminium than
with steel, and much more shaping by wheeling is
possible in the case of aluminium than with harder
metals like mild steel. Thus too much pressure
could have the effect of overstretching the particular
panel or workpiece. The wheeling machine
may be used simply to planish, producing a smooth
surface by the friction and rolling action derived
from passing the sheet backwards and forwards
between the wheels when these have just the right
amount of pressure.
Where components of moderate curvature are to
be produced by wheeling alone, the sheet or blank
is placed between the two wheels at one edge or in
the case of a round blank in the centre; pressure of
the exact amount suitable for both the thickness
and the type of material is applied and the sheet is
wheeled. In the case of aluminium the wheeling
lines are difficult to see, but by smearing the surface
of the panel or sheet with mineral turpentine
or very light oil these tracks become more easily
seen and are therefore more easily lapped. Care
should be taken at this stage when passing the
metal through the wheels not to twist or jerk the
panel, as this could result in ridged sections and an
uneven surface. Movement of the sheet is varied
until the desired shape is obtained, those parts of
the panel which require to be only slightly curved
receiving less wheeling than other parts which must
be more curved.
To wheel a panel that has been preshaped by
blocking in a sandbag, it is necessary to smooth
its surface without altering its shape, and for this
reason the panel should be pulled right through
the wheels at every stroke. This edge-to-edge
wheeling will result in an evenly stretched panel
surface. When carrying out this smoothing work,
or planishing as it could be termed, the pressure
exerted on the work by the wheels should be very
slight. Another common task that can be successfully
carried out with the wheeling machine is to
tighten up the loose wavy edges which sometimes
Figure 13.10The technique of wheeling
(Autokraft Ltd )
348Repair of Vehicle Bodies
occur when shaping a panel by hand. The method
of overcoming this trouble is to wheel directly
adjacent to the stretched edge. This stretches the
area being wheeled and so tightens up the loose
edge. The reverse sort of problem, that of a panel
with a fullness or stretched area just in from the
edge of the sheet, can also be overcome by
wheeling. The method is to start wheeling from
the centre of the fullness on a track parallel to the
edge and to work right out to the edge of the panel.
With most machines three standard wheels are
supplied which are generally referred to as flat,
medium and full curved. The widths of the wheel
tracks are flat 25 mm (1 in), medium 10 mm ( in),
and full curve 5 mm ( in). The best rule to follow
when selecting a wheel is to use the flattest wheel
possible for the job you are doing. This not only
speeds up the wheeling but prevents to a large
extent marking the surface of the panel with wheel
tracks, which are really the evidence of an overstretched
panel (Figure 13.11).
4 When wheeling, the panel should be held without
tension, allowing it to move freely without
twisting or jerking it.
5 The wheel tracks must be carefully overlapped
to achieve a smooth curved surface.